The short answer
SureBreeze AC Repair Service repairs furnaces in Union City homes, including ignition failures, cold air from the vents, short cycling, and noisy blowers. We diagnose the cause, explain it before we start work, and test the system before we leave. Bay Area Air District rules won't force you to replace a furnace that still works.
Most Union City homes don't run the furnace hard for much of the year, so problems tend to show up all at once. On the first cool night of fall, the thermostat clicks and nothing happens, or the system runs but blows cool air. SureBreeze AC Repair Service repairs furnaces across Union City and the 94587 ZIP code from our base in Fremont, about 4 miles to the southeast. We find the actual fault, explain it in plain terms, and fix it so your home stays comfortable through the damp winter months.
Furnace problems we see in Union City homes
Many furnaces here sit unused for months and then get switched on when temperatures drop. Dust settles on burners and sensors, filters get forgotten, and small issues from last winter come back. That pattern leads to a familiar set of service calls:
- The furnace won't ignite, or it lights and then shuts off after a few seconds. A dirty flame sensor or a failed igniter is a common cause.
- The blower runs, but the air coming out of the vents is cool.
- The system short cycles, turning on and off repeatedly without warming the house.
- The burners or blower motor make banging, scraping, or squealing sounds.
- Some rooms stay cold while others overheat.
- The thermostat doesn't seem to control the furnace at all.
- A burning smell lasts beyond the first few minutes of the season.
What happens during a furnace repair visit
We start with the symptoms you've noticed and any error code blinking on the control board. Then we check the system in order: thermostat signal, power and safety switches, ignition sequence, gas pressure, flame quality, venting, blower operation, and airflow through the filter and ducts.
Once we find the cause, we explain it and tell you what the repair involves before we do the work. Common fixes include:
Before we leave, we run the furnace through full heating cycles to confirm it lights, heats, and shuts down the way it should.
- Cleaning or replacing a flame sensor
- Replacing an igniter, pressure switch, inducer motor, blower capacitor, or control board
- Fixing airflow problems caused by clogged filters or blocked returns
Should you repair or replace? What Bay Area rules mean for you
Some Union City homeowners worry that new air quality rules will force them to replace a working furnace. They won't. The Bay Area Air District's appliance rules don't require you to replace working equipment. They apply only when an existing furnace fails or is replaced.
The long-term picture is changing, though. Under the Air District's Rule 9-4, natural gas furnaces manufactured from 2029 onward must meet a zero-NOx emission standard. In practice, that points homeowners toward heat pumps when they replace a furnace after that date. If your furnace is in good shape, repairing it is usually the sensible choice. If it's older and needs a major part, compare the cost of that repair with planning a heat pump installation on your own timeline.
About incentives: the federal Energy Efficient Home Improvement Credit (25C) covered qualifying heat pumps placed in service before December 31, 2025. It isn't available for new installations now. You can check BayREN and your local clean energy provider for current heat pump and electrification incentives. Amounts and availability change with each funding cycle, so we confirm the current offer before we quote it.
Furnace warning signs that need attention right away
Some problems shouldn't wait for a scheduled visit. If you smell gas, leave the house first, then call your gas utility or 911 from outside. If a carbon monoxide alarm goes off, get everyone out and call 911. Once the home has been cleared as safe, turn the furnace off and call us for a repair if you notice any of these:
- Soot or scorch marks around the furnace cabinet or vent pipe
- A yellow, flickering burner flame instead of a steady blue one
- Water pooling around a high-efficiency furnace
- A breaker that trips every time the furnace starts
Serving Union City and nearby communities
Union City is a short drive from our Fremont base, and we serve homes throughout 94587 in Alameda County. We also repair furnaces in Hayward, Newark, Pleasanton, Dublin, and Menlo Park. When you contact us, tell us what the furnace is doing, roughly how old it is, and whether it's a standard or high-efficiency model. That helps us bring the right parts and get your heat back sooner.
More services in Union City
- AC Repair in Union City
- Heating Repair in Union City
- Heat Pump Installation in Union City
- AC Installation in Union City

